{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. Current working directory is set to:  c:\ladybug\unnamed\OpenStudio
3. Duplicate surface name! Name is changed to: wall3_Dup
4. Currently OpenStudio component des not support .csv file as a schedule.
The schedule: C:\LADYBUG\EPCSVSCHEDULES\SCHMORBLINDSSCHEDULE.CSV will be written into IDF after it is translated from an OSM.
5. Currently OpenStudio component des not support .csv file as a schedule.
The schedule: C:\LADYBUG\EPCSVSCHEDULES\SCHMORBLINDSSCHEDULE.CSV will be written into IDF after it is translated from an OSM.
6. Currently OpenStudio component des not support .csv file as a schedule.
The schedule: C:\LADYBUG\EPCSVSCHEDULES\SCHMORBLINDSSCHEDULE.CSV will be written into IDF after it is translated from an OSM.
7. Currently OpenStudio component des not support .csv file as a schedule.
The schedule: C:\LADYBUG\EPCSVSCHEDULES\SCHMORBLINDSSCHEDULE.CSV will be written into IDF after it is translated from an OSM.
8. too many values to unpack
9. Model saved to: c:\ladybug\unnamed\OpenStudio\unnamed.osm
10. OSM > IDF: c:/ladybug/unnamed/OpenStudio/unnamed/ModelToIdf/in.idf
11. Program Version,EnergyPlus, Version 9.2.0-921312fa1d, YMD=2020.04.14 10:28,
12. 
13.    ************* Beginning Zone Sizing Calculations
14. 
15.    ** Warning ** ProcessScheduleInput: Schedule:Constant="ALWAYS OFF DISCRETE", Blank Schedule Type Limits Name input -- will not be validated.
16. 
17.    ** Warning ** GetHTSurfaceData: Surfaces with interface to Ground found but no "Ground Temperatures" were input.
18. 
19.    **   ~~~   ** Found first in surface=FLOOR4
20. 
21.    **   ~~~   ** Defaults, constant throughout the year of (18.0) will be used.
22. 
23.    ** Warning ** WindowShadingControl="SHADING CONTROL 1", The first SetPoint is zero.
24. 
25.    **   ~~~   ** ..You may have forgotten to specify that setpoint.
26. 
27.    ** Warning ** WindowShadingControl="SHADING CONTROL 2", The first SetPoint is zero.
28. 
29.    **   ~~~   ** ..You may have forgotten to specify that setpoint.
30. 
31.    ** Warning ** WindowShadingControl="SHADING CONTROL 3", The first SetPoint is zero.
32. 
33.    **   ~~~   ** ..You may have forgotten to specify that setpoint.
34. 
35.    ** Warning ** WindowShadingControl="SHADING CONTROL 4", The first SetPoint is zero.
36. 
37.    **   ~~~   ** ..You may have forgotten to specify that setpoint.
38. 
39.    ************* Note that the following warning(s) may/will occur if you have not enclosed your zone completely.
40. 
41.    ** Warning ** Entered Zone Volumes differ from calculated zone volume(s).
42. 
43.    **   ~~~   ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual zones.
44. 
45.    ** Warning ** CheckUsedConstructions: There are 2 nominally unused constructions in input.
46. 
47.    **   ~~~   ** For explicit details on each unused construction, use Output:Diagnostics,DisplayExtraWarnings;
48. 
49.    ** Warning ** AssociateWindowShadingControlWithDaylighting: Daylighting object name used in WindowShadingControl not found.
50. 
51.    **   ~~~   ** ..The WindowShadingControl object="SHADING CONTROL 1" and referenes an object named: ""
52. 
53.    ** Warning ** AssociateWindowShadingControlWithDaylighting: Daylighting object name used in WindowShadingControl not found.
54. 
55.    **   ~~~   ** ..The WindowShadingControl object="SHADING CONTROL 2" and referenes an object named: ""
56. 
57.    ** Warning ** AssociateWindowShadingControlWithDaylighting: Daylighting object name used in WindowShadingControl not found.
58. 
59.    **   ~~~   ** ..The WindowShadingControl object="SHADING CONTROL 3" and referenes an object named: ""
60. 
61.    ** Warning ** AssociateWindowShadingControlWithDaylighting: Daylighting object name used in WindowShadingControl not found.
62. 
63.    **   ~~~   ** ..The WindowShadingControl object="SHADING CONTROL 4" and referenes an object named: ""
64. 
65.    ** Warning ** UpdateZoneSizing: Cooling supply air temperature (calculated) within 5C of zone temperature
66. 
67.    **   ~~~   ** ...check zone thermostat set point and design supply air temperatures
68. 
69.    **   ~~~   ** ...zone name = BEDROOM1
70. 
71.    **   ~~~   ** ...design sensible cooling load = 1295.14 W
72. 
73.    **   ~~~   ** ...thermostat set point temp    = 0.000 C
74. 
75.    **   ~~~   ** ...zone temperature             = 21.500 C
76. 
77.    **   ~~~   ** ...supply air temperature       = 18.000 C
78. 
79.    **   ~~~   ** ...temperature difference       = -3.49983 C
80. 
81.    **   ~~~   ** ...calculated volume flow rate  = 0.30099 m3/s
82. 
83.    **   ~~~   ** ...calculated mass flow rate    = 0.36258 kg/s
84. 
85.    ** Warning ** UpdateZoneSizing: Cooling supply air temperature (calculated) within 5C of zone temperature
86. 
87.    **   ~~~   ** ...check zone thermostat set point and design supply air temperatures
88. 
89.    **   ~~~   ** ...zone name = BEDROOM2
90. 
91.    **   ~~~   ** ...design sensible cooling load = 1752.47 W
92. 
93.    **   ~~~   ** ...thermostat set point temp    = 0.000 C
94. 
95.    **   ~~~   ** ...zone temperature             = 21.500 C
96. 
97.    **   ~~~   ** ...supply air temperature       = 18.000 C
98. 
99.    **   ~~~   ** ...temperature difference       = -3.49976 C
100. 
101.    **   ~~~   ** ...calculated volume flow rate  = 0.40729 m3/s
102. 
103.    **   ~~~   ** ...calculated mass flow rate    = 0.49061 kg/s
104. 
105.    ** Warning ** UpdateZoneSizing: Cooling supply air temperature (calculated) within 5C of zone temperature
106. 
107.    **   ~~~   ** ...check zone thermostat set point and design supply air temperatures
108. 
109.    **   ~~~   ** ...zone name = LIVINGROOM
110. 
111.    **   ~~~   ** ...design sensible cooling load = 1236.66 W
112. 
113.    **   ~~~   ** ...thermostat set point temp    = 0.000 C
114. 
115.    **   ~~~   ** ...zone temperature             = 21.499 C
116. 
117.    **   ~~~   ** ...supply air temperature       = 18.000 C
118. 
119.    **   ~~~   ** ...temperature difference       = -3.49934 C
120. 
121.    **   ~~~   ** ...calculated volume flow rate  = 0.28744 m3/s
122. 
123.    **   ~~~   ** ...calculated mass flow rate    = 0.34625 kg/s
124. 
125.    ************* Beginning System Sizing Calculations
126. 
127.    ** Warning ** GetAirPathData: AirLoopHVAC="AIR LOOP HVAC 1" has no Controllers.
128. 
129.    ************* Beginning Plant Sizing Calculations
130. 
131.    ** Warning ** Capacity ratio as a function of temperature curve output is not equal to 1.0
132. 
133.    **   ~~~   ** (+ or - 10%) at reference conditions for ChillerHeaterPerformance:Electric:EIR= CHILLER HEATER PERFORMANCE ELECTRIC EIR 1
134. 
135.    **   ~~~   ** Curve output at reference conditions = 1.202
136. 
137.    ** Warning ** Energy input ratio as a function of temperature curve output is not equal to 1.0
138. 
139.    **   ~~~   ** (+ or - 10%) at reference conditions for ChillerHeaterPerformance:Electric:EIR= CHILLER HEATER PERFORMANCE ELECTRIC EIR 1
140. 
141.    **   ~~~   ** Curve output at reference conditions = 0.656
142. 
143.    ** Warning ** Missing temperature setpoint on cooling side for CentralHeatPumpSystem named CENTRAL HEAT PUMP SYSTEM 1
144. 
145.    **   ~~~   **   A temperature setpoint is needed at the outlet node of a CentralHeatPumpSystem, use a SetpointManager
146. 
147.    **   ~~~   **   The overall loop setpoint will be assumed for CentralHeatPumpSystem. The simulation continues ... 
148. 
149.    ** Warning ** Missing temperature setpoint on heating side for CentralHeatPumpSystem named CENTRAL HEAT PUMP SYSTEM 1
150. 
151.    **   ~~~   **   A temperature setpoint is needed at the outlet node of a CentralHeatPumpSystem, use a SetpointManager
152. 
153.    **   ~~~   **   The overall loop setpoint will be assumed for CentralHeatPumpSystem. The simulation continues ... 
154. 
155.    ************* Testing Individual Branch Integrity
156. 
157.    ************* All Branches passed integrity testing
158. 
159.    ************* Testing Individual Supply Air Path Integrity
160. 
161.    ************* All Supply Air Paths passed integrity testing
162. 
163.    ************* Testing Individual Return Air Path Integrity
164. 
165.    ************* All Return Air Paths passed integrity testing
166. 
167.    ************* No node connection errors were found.
168. 
169.    ************* Beginning Simulation
170. 
171.    ** Severe  ** CalcHeatBalanceInsideSurf: The temperature of 3809161.94 C for zone="BEDROOM1", for surface="FLOOR1"
172. 
173.    **   ~~~   ** ..is very far out of bounds during warmup. This may be an indication of a malformed zone.
174. 
175.    **   ~~~   **  During Warmup, Environment=RUN PERIOD 1, at Simulation time=01/01 14:30 - 14:31
176. 
177.    **  Fatal  ** Program terminates due to preceding condition.
178. 
179.    ...Summary of Errors that led to program termination:
180. 
181.    ..... Reference severe error count=1
182. 
183.    ..... Last severe error=CalcHeatBalanceInsideSurf: The temperature of 3809161.94 C for zone="BEDROOM1", for surface="FLOOR1"
184. 
185.    ** Warning ** Check control types on branches between splitter and mixer in PlantLoop=CONDENSER WATER LOOP
186. 
187.    **   ~~~   ** Found a BYPASS branch with no ACTIVE branch in parallel with it
188. 
189.    **   ~~~   ** In certain (but not all) situations, this can cause problems; please verify your inputs
190. 
191.    **   ~~~   ** Bypass branch named: CONDENSER WATER LOOP DEMAND BRANCH 1
192. 
193.    ** Warning ** Check control types on branches between splitter and mixer in PlantLoop=CONDENSER WATER LOOP
194. 
195.    **   ~~~   ** Found a BYPASS branch with no ACTIVE branch in parallel with it
196. 
197.    **   ~~~   ** In certain (but not all) situations, this can cause problems; please verify your inputs
198. 
199.    **   ~~~   ** Bypass branch named: CONDENSER WATER LOOP DEMAND BYPASS BRANCH
200. 
201.    *************
202. 
203.    ************* ===== Recurring Error Summary =====
204. 
205.    ************* The following recurring error messages occurred.
206. 
207.    *************
208. 
209.    *************  ** Warning ** Plant loop exceeding upper temperature limit, PlantLoop="CHILLED WATER LOOP"
210. 
211.    *************  **   ~~~   **   This error occurred 78 total times;
212. 
213.    *************  **   ~~~   **   during Warmup 78 times;
214. 
215.    *************  **   ~~~   **   during Sizing 0 times.
216. 
217.    *************  **   ~~~   **   Max=60.
218. 
219.    *************
220. 
221.    *************
222. 
223.    ************* ===== Final Error Summary =====
224. 
225.    ************* The following error categories occurred.  Consider correcting or noting.
226. 
227.    ************* Nominally Unused Constructions
228. 
229.    ************* ..The nominally unused constructions warning is provided to alert you to potential conditions that can cause
230. 
231.    ************* ..extra time during simulation. Each construction is calculated by the algorithm indicated in the HeatBalanceAlgorithm
232. 
233.    ************* ..object. You may remove the constructions indicated (when you use the DisplayExtraWarnings option).
234. 
235.    *************
236. 
237.    ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 1 Severe Errors.
238. 
239.    ************* EnergyPlus Sizing Error Summary. During Sizing: 16 Warning; 0 Severe Errors.
240. 
241.    ************* EnergyPlus Terminated--Fatal Error Detected. 100 Warning; 1 Severe Errors; Elapsed Time=00hr 00min  6.76sec
242.