{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. Current working directory is set to:  c:\ladybug\unnamed\OpenStudio
3. Duplicate surface name! Name is changed to: roof3_Dup
4. Duplicate surface name! Name is changed to: wall3_Dup
5. Currently OpenStudio component des not support .csv file as a schedule.
The schedule: C:\LADYBUG\EPCSVSCHEDULES\SCHMORBLINDSSCHEDULE.CSV will be written into IDF after it is translated from an OSM.
6. Model saved to: c:\ladybug\unnamed\OpenStudio\unnamed.osm
7. OSM > IDF: c:/ladybug/unnamed/OpenStudio/unnamed/ModelToIdf/in.idf
8. Program Version,EnergyPlus, Version 9.2.0-921312fa1d, YMD=2020.04.15 11:19,
9. 
10.    ************* Beginning Zone Sizing Calculations
11. 
12.    ** Warning ** ProcessScheduleInput: Schedule:Constant="ALWAYS OFF DISCRETE", Blank Schedule Type Limits Name input -- will not be validated.
13. 
14.    ** Warning ** ProcessScheduleInput: Schedule:Constant="ALWAYS ON CONTINUOUS", Blank Schedule Type Limits Name input -- will not be validated.
15. 
16.    ** Warning ** WindowShadingControl="SHADING CONTROL 1", The first SetPoint is zero.
17. 
18.    **   ~~~   ** ..You may have forgotten to specify that setpoint.
19. 
20.    ************* Note that the following warning(s) may/will occur if you have not enclosed your zone completely.
21. 
22.    ** Warning ** Entered Zone Volumes differ from calculated zone volume(s).
23. 
24.    **   ~~~   ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual zones.
25. 
26.    ** Warning ** CheckUsedConstructions: There are 2 nominally unused constructions in input.
27. 
28.    **   ~~~   ** For explicit details on each unused construction, use Output:Diagnostics,DisplayExtraWarnings;
29. 
30.    ** Warning ** UpdateZoneSizing: Cooling supply air temperature (calculated) within 5C of zone temperature
31. 
32.    **   ~~~   ** ...check zone thermostat set point and design supply air temperatures
33. 
34.    **   ~~~   ** ...zone name = LIVINGROOM
35. 
36.    **   ~~~   ** ...design sensible cooling load = 1871.34 W
37. 
38.    **   ~~~   ** ...thermostat set point temp    = 0.000 C
39. 
40.    **   ~~~   ** ...zone temperature             = 21.499 C
41. 
42.    **   ~~~   ** ...supply air temperature       = 18.000 C
43. 
44.    **   ~~~   ** ...temperature difference       = -3.49882 C
45. 
46.    **   ~~~   ** ...calculated volume flow rate  = 0.43503 m3/s
47. 
48.    **   ~~~   ** ...calculated mass flow rate    = 0.52404 kg/s
49. 
50.    ************* Beginning System Sizing Calculations
51. 
52.    ** Warning ** GetAirPathData: AirLoopHVAC="AIR LOOP HVAC 1" has no Controllers.
53. 
54.    ************* Beginning Plant Sizing Calculations
55. 
56.    ** Warning ** Capacity ratio as a function of temperature curve output is not equal to 1.0
57. 
58.    **   ~~~   ** (+ or - 10%) at reference conditions for ChillerHeaterPerformance:Electric:EIR= CHILLER HEATER PERFORMANCE ELECTRIC EIR 1
59. 
60.    **   ~~~   ** Curve output at reference conditions = 1.202
61. 
62.    ** Warning ** Energy input ratio as a function of temperature curve output is not equal to 1.0
63. 
64.    **   ~~~   ** (+ or - 10%) at reference conditions for ChillerHeaterPerformance:Electric:EIR= CHILLER HEATER PERFORMANCE ELECTRIC EIR 1
65. 
66.    **   ~~~   ** Curve output at reference conditions = 0.656
67. 
68.    ** Warning ** Missing temperature setpoint on cooling side for CentralHeatPumpSystem named CENTRAL HEAT PUMP SYSTEM 1
69. 
70.    **   ~~~   **   A temperature setpoint is needed at the outlet node of a CentralHeatPumpSystem, use a SetpointManager
71. 
72.    **   ~~~   **   The overall loop setpoint will be assumed for CentralHeatPumpSystem. The simulation continues ... 
73. 
74.    ** Warning ** Missing temperature setpoint on heating side for CentralHeatPumpSystem named CENTRAL HEAT PUMP SYSTEM 1
75. 
76.    **   ~~~   **   A temperature setpoint is needed at the outlet node of a CentralHeatPumpSystem, use a SetpointManager
77. 
78.    **   ~~~   **   The overall loop setpoint will be assumed for CentralHeatPumpSystem. The simulation continues ... 
79. 
80.    ************* Testing Individual Branch Integrity
81. 
82.    ************* All Branches passed integrity testing
83. 
84.    ************* Testing Individual Supply Air Path Integrity
85. 
86.    ************* All Supply Air Paths passed integrity testing
87. 
88.    ************* Testing Individual Return Air Path Integrity
89. 
90.    ************* All Return Air Paths passed integrity testing
91. 
92.    ************* No node connection errors were found.
93. 
94.    ************* Beginning Simulation
95. 
96.    ** Severe  ** CalcHeatBalanceInsideSurf: The temperature of 1588779.89 C for zone="LIVINGROOM", for surface="FACADE4"
97. 
98.    **   ~~~   ** ..is very far out of bounds during warmup. This may be an indication of a malformed zone.
99. 
100.    **   ~~~   **  During Warmup, Environment=RUN PERIOD 1, at Simulation time=01/01 03:21 - 03:23
101. 
102.    **  Fatal  ** Program terminates due to preceding condition.
103. 
104.    ...Summary of Errors that led to program termination:
105. 
106.    ..... Reference severe error count=1
107. 
108.    ..... Last severe error=CalcHeatBalanceInsideSurf: The temperature of 1588779.89 C for zone="LIVINGROOM", for surface="FACADE4"
109. 
110.    ** Warning ** Check control types on branches between splitter and mixer in PlantLoop=CONDENSER WATER LOOP
111. 
112.    **   ~~~   ** Found a BYPASS branch with no ACTIVE branch in parallel with it
113. 
114.    **   ~~~   ** In certain (but not all) situations, this can cause problems; please verify your inputs
115. 
116.    **   ~~~   ** Bypass branch named: CONDENSER WATER LOOP DEMAND BRANCH 1
117. 
118.    ** Warning ** Check control types on branches between splitter and mixer in PlantLoop=CONDENSER WATER LOOP
119. 
120.    **   ~~~   ** Found a BYPASS branch with no ACTIVE branch in parallel with it
121. 
122.    **   ~~~   ** In certain (but not all) situations, this can cause problems; please verify your inputs
123. 
124.    **   ~~~   ** Bypass branch named: CONDENSER WATER LOOP DEMAND BYPASS BRANCH
125. 
126.    *************
127. 
128.    ************* ===== Final Error Summary =====
129. 
130.    ************* The following error categories occurred.  Consider correcting or noting.
131. 
132.    ************* Nominally Unused Constructions
133. 
134.    ************* ..The nominally unused constructions warning is provided to alert you to potential conditions that can cause
135. 
136.    ************* ..extra time during simulation. Each construction is calculated by the algorithm indicated in the HeatBalanceAlgorithm
137. 
138.    ************* ..object. You may remove the constructions indicated (when you use the DisplayExtraWarnings option).
139. 
140.    *************
141. 
142.    ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 1 Severe Errors.
143. 
144.    ************* EnergyPlus Sizing Error Summary. During Sizing: 7 Warning; 0 Severe Errors.
145. 
146.    ************* EnergyPlus Terminated--Fatal Error Detected. 13 Warning; 1 Severe Errors; Elapsed Time=00hr 00min  0.96sec
147.