I got a result address but no actual result csv file

grasshopper honeybee-legacy
8

@FabianPosadas @MohammedAlshayeb
Here it is …
its a follow of one of @chris tutorials on YouTube

lesson 7.gh (602.1 KB)

9

It runs and I got the results without changing anything !!

You still have an error but that is related to non-convex surface. The error can be fixed by setting “0” to SolarDistribution under energySimPar.

2 Likes
10

You need to add energysimPar and change the solar distribution to 0. The model you are using has nonconvex surfaces which is creating a solar distribution error.

image
image.png1799×671 97.1 KB

1 Like
11

you beat me to the punch by seconds. lol :wink:

2 Likes
12

@MohammedAlshayeb & @FabianPosadas …
I did that but unfortunately the error stills!
This is so strange Mohammed … don’t no what to do if it is Okay in your side!

Thx anyway … and I am still trying to figure out …

but by the way … how can I discover that convexity problem?

13

To your main issue, sometime what you have to do is to reconnect the wire again or replace the component with a new one.

Regarding the non-convex, read this:

14

@MohammedAlshayeb thanks for you kind replys …

I will restart my lap and will try again … then back to you

and thanks for the details …

15

@MohammedAlshayeb
I got this warnings out from the Honeybee_Honeybee component …

hi1
hi1.png815×486 38.8 KB

Any suggestion to get them solved … I think this may holds the solution …

16

The solution is here:

1 Like
17

Thx @FabianPosadas … that solved every previous problems …

But another problem has appeared :frowning: … says:

hi2
hi2.png870×523 56.6 KB

18

It still the latest .gh file I have uploaded … and you told me that it worked correctly …

19

That is happening because you don’t have a value entered for max angle. Did you change it? the model you uploaded shows it at 45 degrees. But I saw that error when that input was removed.

1 Like
20

Hi @FabianPosadas
The angle still the same 45 degree … and that’s the thing which confuse!

21

Interesting, I’m getting the exact same issue with my idf run, but it runs fine with the openstudio run instead. In making a public share version of my file (as a lot within it contains commercially sensitive items), it worked. I considered perhaps there are some items in the stream causing issues, but after systematically removing nodes at a time, there was no problem.

There was an issue with OSM run component initially when my units were still in millimeters saying “E:\Git\OS1\openstudiocore\src\model\PlanarSurface.cpp@627 : Cannot create a surface …” but was resolved when i changed it to meters. Screen below of the idf run not seeming to work, with OSM error:

image
image.png1069×816 115 KB

And screen shot of OSM working with result files but idf being strange.

image
image.png1065×836 104 KB

It worked on off and odd times, so perhaps just requires reloads.

1 Like
22

Thank you very much @ElzineBraasch for detailed clarification …
I will be back to my work after updating the geometry and consider your advice if it appeared again …

1 Like
23

I am facing the same issue as above. The analysis is running, but no .csv file generated.

I have tried all the above stated fixes but the file does not generate .csv files.

I’m attaching my rhino and gh files.

Thanks

Test.3dm (46.9 KB)
Test.gh (598.4 KB)

24

@MansiDhanuka,
tried your file. It runs fine and writes the .csv on my machiine.

25

@devang Thank you for the quick response.

What is the fix for my machine then? I have reinstalled everything.

Thanks
Mansi

26

you sure you have write access?

27

How do I write access? Can you explain?

I installed everything with default settings. HB LB Energyplus are up to date as well.

Thanks